一个皇家海军“胜利”号截面的场景（2）

old_cobra

本来以为就昨天发的那些，结果发现又有新的更新，今天接着发~~

    I am now up to the lower gun deck.  I needed to make the three 32 pounder cannons for this section of the deck.  I turned a master out of wood and proceeded to make a box, lined the bottom with clay and made a two part mold.  I took the mold and poured resin into it to make my cannons.  I was able to take the resin cannons and mount them on the lathe to clean and refine them.  Necessary components to the cannons were made, painted and added.  I made the ceiling for the lower gun deck trying to place the carlings and ledges in their proper place.  The two part capstan I turned and mounted  the lower half.

我现在要做下层炮甲板。我需要在这个甲板部分制作三门32磅大炮。我镟制木头的母版，放入一个盒子，底部衬垫粘土，做出一个两个部分的模具。我把树脂浇到模具里做出我的大炮。我会把树脂大炮安放到车床上，清理和完善它们。把必要的组成部分加到已经做好的大炮上，涂上油漆。我为下层甲板制作顶棚，试着安放到纵梁和支架上的合适位置。我镟制并安放两组分绞盘的下半部。

old_cobra

[fbdsbsb] [fbdsbsb] [fbdsbsb]


    Now came for the real test, to make the figures, hopefully showing some action.  I used  various sources for the figures.  Most of them started as Micro Agression wrestlers.  They are very near 1/32 scale.  I did file some of their muscles off and in many instances only used from the waist up.  I duplicated many pants/trousers from other 1/32 scale figures I had and used them in junction with many wrestlers.  Arms had to be cut off and re-adjusted to show the action I wanted them to portray.  There are 17 figures on the lower gun deck.  The marine (in red) I made from a Preiser Prussians 1756 set.  The Prussian was modified  with filing, cutting and epoxy putty.  For many of the wrestlers I changed heads using the Preiser model figure Adam set.

现在，在真正的考验来了，制作人偶，希望表现出一些行为。我用不同来源的人偶。它们大多开始像一个微型摔跤手。他们非常接近1/32的比例。我锉一些他们的肌肉，在许多情况下只用于从腰部以上。我从其他1/32比例的人偶那里复制了许多裤子/长裤，把它们套在的炮手身上。切断它们的手臂再重新调整，以显示我想描绘的它们的行动。下层炮甲板上有17个人偶。水兵（红色），我从一套1756年的贝尔瑟普鲁士人制作的。用锉、刀和环氧油灰修改普鲁士人。我使用贝尔瑟模型人偶亚当套件改变许多炮手的头脸。

old_cobra

[fbdsbsb] [fbdsbsb] [fbdsbsb]

     Now for some photos with the ceiling of the lower gun deck (floor of the middle gun deck) in place.  The cannon on the far left is being readied to load.  The one in the middle is being pulled up and adjusted to fire it and the one on the right is set for firing.  These photos hopefully will show how confine the space was on the lower gun deck of the HMS Victory.  At this point in the build (I'm about half way) I have over 421 hours of work into this project.  Now on to the middle gun deck.

现在一些带下层甲板的顶棚的照片（中炮甲板的地板）到位。最左侧的大炮正在准备装填。中间的一个正在拔出和调整导火索，右面的一个在正确的为发射做准备。这些照片希望展示“胜利”号下层炮甲板上的空间如何有限。在这一点上的制作（我走了大约一半的路）我在这个项目上的工作已超过421小时。现在要制作中炮甲板。

714333695

好羡慕啊！！！！！！！！！！

saill

好东东啊，又深入的学习了[vse4bb][vse4bb]

淡泊中年

场景热火朝天，很不错。下载收藏了

奥比王

估计这个场景模型完成至少需要600小时，大工程啊！
很多玩家想找船模用的水手，通过此贴我感觉在国外这种人物模型也是很难找的，大部分应该也是用这种方法，用其他人物来改。[sbsbs]

aucmaswcw

[vse4bb][vse4bb]很棒的场景

郭大路

人遇做得真好